Home / Gainesville / Service area / High Springs

Mold Remediation in High Springs, FL

PureGuard Restoration removes mold from homes and buildings in High Springs and along the Santa Fe River. Here is why river flooding changes the mold problem.

The short answer

Mold help for High Springs after leaks and river flooding

PureGuard Restoration is a Gainesville mold remediation contractor, and High Springs is part of our service area. If you can see or smell mold, or water has been in your home for more than a day or two, send photos through our quote form or call (352) 668-9909. We will tell you honestly whether it is a job you can handle, a leak to fix first, or work for a licensed remediator. We do not test for mold. For testing or a clearance check, we point you to an independent licensed assessor.

High Springs differs from the rest of the county in one way that matters for mold: the Santa Fe River. When a river floods, the water arrives slowly and leaves slowly, and that changes what happens inside a house.

Local picture

What makes High Springs different

  • A railroad town on the Santa Fe. The Savannah, Florida and Western Railway was built here in the early 1880s, and a station and post office called Santaffey opened in 1884. The city is the fourth-largest in Alachua County.
  • Steady growth. The 2020 census counted 6,215 residents, up from 5,350 in 2010, about 16 percent. Its ZIP codes are 32643 and 32655.
  • Northwest of Gainesville. The city sits along US 441, and the sandbag site offered to river residents in 2024 was on US 441.
  • River-front properties. Properties along the river, including areas off Southeast Resort Circle and near Hornsby Spring, are the ones local reporting named as at risk when the river runs high.

River flooding

When the Santa Fe River rises

A flash flood from a downpour can drain within hours. River flooding is different. In December 2018, Alachua County warned that levels on the Santa Fe River near High Springs were expected to keep rising after more rain, and the boat ramp south of US 441 was already underwater.

In August 2024, after Hurricane Debby, the forecast for the Santa Fe River near High Springs called for a crest of 44.1 feet as early as August 9. The river’s historic high there is 48.5 feet. Local reporting said that above 43 feet, homes off Southeast Resort Circle and near Hornsby Spring could flood, and the county offered self-service sandbags at 17380 NW US Highway 441, limited to 10 per vehicle, to residents with property along the river.

The mold problem comes from how long things stay wet. Slow-rising, slow-falling water can saturate a crawl space, a slab or the lower walls for days or weeks, and wet drywall and insulation can grow mold in the 24 to 48 hours EPA gives for drying. Flood-soaked porous materials are usually discarded, not dried in place. Our page on mold after a hurricane or flood explains what to save and what to throw away.

Floods and insurance

Flood damage and mold coverage

Homeowners policies generally do not cover flood damage, which is usually insured separately, and mold coverage often depends on the water event that caused it. Read your policies before you start work, photograph everything before you remove it and keep receipts. Our guides to homeowners coverage for mold and the mold claim checklist explain what to gather, and the mold sublimit page covers the usual caps.

After the water

What to do after river water leaves your home

  • Wait until it is safe to enter, and turn off electricity at the breaker only if you can do so without standing in water.
  • Photograph the water line and damaged items before you move anything.
  • Remove wet carpet, padding and soaked porous materials, and open the house to dry.
  • Use fans and a dehumidifier. EPA recommends indoor humidity below 60 percent, ideally 30 to 50 percent.
  • Do not run a heating and cooling system that was in the water.
  • Check crawl spaces, under-floor insulation and ducts, which can stay wet long after the living area looks dry.
  • Call a licensed remediator when mold covers more than about 10 square feet or when drywall and insulation were soaked.

The job

What to expect when we work in High Springs

We start with the moisture source, because EPA says cleanup is not finished until the water problem is fixed. You then receive a written scope of work that says what will be removed, what will be cleaned, how the area will be contained and how the result will be checked. Our guide to reading a mold remediation quote and the process page explain each step. Cost guides commonly show $10 to $25 per square foot and single-room jobs between $1,500 and $6,000, and flood jobs with extensive tear-out can cost more. These are statewide ranges, not High Springs prices. See the cost page. After a regional flood, appointments get scarce, so sending photos early helps us plan.

Neighbors

Renters, owners and nearby towns

If you own a cabin or second home on the river and are away during high water, ask a neighbor or property manager to check on it afterward, because a wet house left shut up can grow mold quickly. Renters should give the landlord written notice, and our mold notice letter helps. We also serve Alachua and Newberry. See the service area and the mold season calendar.

Questions

Questions from High Springs homeowners

Do you serve High Springs?

We serve High Springs and the surrounding area from our Gainesville base. Give us your address or ZIP code when you ask for a quote and we will confirm.

Does river flooding cause more mold than rain?

It can, because river water stays high longer, so materials stay wet longer. The 24 to 48 hour drying window EPA gives is hard to meet, which is why tear-out and fast drying matter after a river flood.

Do you test for mold?

No. PureGuard Restoration is a remediation contractor. For testing or a clearance check, use an independent licensed assessor.

Get a quote

Get a written quote for your High Springs mold problem

Send a few photos and a short description, and PureGuard Restoration will come back with a written scope of work and price. We will get back to you as soon as we can.

Ask for the license number when someone calls you back. You can check it on the state lookup.

About us: PureGuard Restoration is a mold remediation company serving Gainesville and Alachua County. We do not test for mold.

Request your written quote

What helps most in the first message

  • Where the mold is and roughly how big it looks. A coin, a hand or a sheet of paper next to it helps.
  • Where you think the water came from, and whether it’s fixed.
  • When you first noticed it, and whether there was a leak, storm or AC problem before that.
  • Whether you own, rent or manage the property, and whether you plan to involve insurance.